Top Slings stocks full range of chain blocks (also known as chain hoist) from Vital, Akita and BST, with capacities from 0.5 tonnes up to 50 tonnes.
We also provide customization services, allowing load chain and hand chain to be extended as per customer requests. Special models such as spark resistant (ATEX approved) chain block, anti-corrosion chain block and stainless steel chain blocks are also available. Feel free to contact us for more information.
Top Slings stocks full range of lever blocks (also known as lever hoists, monkey jack) from Vital, Akita and BST, with capacities from 0.5 tonnes up to 9 tonnes.
We also provide customization services, allowing load chain to be extended as per customer requests. Special models such as spark resistant (ATEX approved) lever block, anti-corrosion lever block and stainless steel lever blocks are also available. Feel free to contact us for more information.
Top Slings stocks full range of Plain Trolley (Push Trolley) and Geared Trolley from Vital and Akita, with capacities from 0.5 tonnes up to 30 tonnes. Trolleys are designed for overhead beam connection, quick attached to monorail and can be combined with other hoisting devices.
Drop stops are equipped to inhibit trolley from moving beyond the designed limit of travel. For heavy duty application requiring working load of more than 4 Tonne, we recommend using trolleys with double shaft.
Special models such as articulated trolley, spark resistant (ATEX approved) trolley, anti-corrosion trolley and stainless steel trolley are also available. Feel free to contact us for more information.
Top Slings stocks wide range of snatch block, consisting of shackle head single sheave snatch block, eye head single sheave snatch block, shackle head double sheave snatch block and eye head double sheave snatch block.
Snatch block is primarily designed to work as a pulley joint that can also redirect wire line in a system. Bigger and customized snatch blocks are also available. Feel free to contact us for more information.
Top Slings stock wide range of clamps consisting of beam clamp, vertical and horizontal plate clamp, vertical and horizontal lifting clamp, pipe plate clamp, universal clamps and screwcam pulling clamps, from reputable manufacturer such as Camlok and BST.
Plate clamps are widely used in steel fabrication industry for handling a variety of work including individual piece of plate, fabricated assemblies and bundles of plates. Beam clamps offers a secure grip to the beam flange, allowing quick and versatile rigging point for hoisting equipment, pulley or loads.
Top Slings stock wide range of hand operated winches and jaw winches (also known as Tiffor, cable puller) from BST and Maxpull Japan.
Stainless steel winches are also available. Feel free to contact us for more information.
Top Slings stock wide range of gear jacks up to 100 Tonne. Gear jacks are designed to apply great forces or lift heavy loads. In addition to any specific instructions relating to safe use of the jack issued by the manufacturer, the following points should be observed:
- The floor must be capable of withstand the load that will be imposed on it by the jacks and the operation must be supervised.
- Over-extension is prohibited.
- Packing must can withstand the crushing effect of the load.
- System of instruction and signals should be used to avoid any confusions.
- Level and even surface should be in place with the jack.
- In any circumstances, there shall be no one working or climbing on a load which is support by jacks.
- Never over-extend a jack or allow anyone to reach under a load supported by jacks.
- Good care must be taken to prevent jack kicking out due to sideways loading and ensure operatives do not trapped by the movement of the load in confined spaces.
- Stability may be enhanced by additional measures where independent cylinders and pumps are employed.
Feel free to contact us for more information.
Top Slings stock wide range of permanent magnetic lifter (also known as lifting magnets), consist of portable model with lifting eye, welding holder model and multiple magnet holder model.
Magnetic lifters (lifting magnets) are normally rated for lifting a horizontal load in the vertical plane only. If the line of pull is not at right angles to the plane of the load, their lifting capacity will be substantially reduced and slippage may occur.
The magnetic lifters (lifting magnets) selected must match the characteristics of the load. This includes the shape, surface finish and magnetic properties of the load. The shape of the magnet should be compatible with that of the load. For example, a magnet with flat face can handle sheet material whereas for lifting round section material, a magnet with V shaped recess in the face is more suitable. For long loads, an arrangement of several magnets used in conjunction with a lifting beam is recommended as it provides the load with adequate supports along its length. The position and capacity of the individual magnets should be such to ensure the shape of the load imposed on each does not exceed its working load limit.
Always consult a competent person before selecting and using permanent magnetic lifter! Feel free to contact us for more information.